Name: International Interprotect High Performance Epoxy Primer
SKU: 162519

International Interprotect is a high performance two pack primer/undercoat. Easy to apply and quick drying,

An epoxy polyamide primer that can be recoated with itself for up to 6 months
Easy to sand and quick to dry
Good abrasion resistance
Offers excellent anticorrosive protection
Can be used as an antifouling tie-coat over existing epoxy primers

Use in these areas

Suitable for above and below waterline

Hull
Bilge/Lockers
Exterior cabin/trims
Interior cabin/trims
Propeller
Drive

Use for substrates

Aluminium / Zinc-Galvanised Steel
Epoxy Composite / Carbon Fibre
GRP / FRP
Lead
Steel
Wood

Pack Size

750ml

Preparation

Steel: Degrease with solvent or Super Cleaner. Grit-blast to Sa 2½ - near white metal surface. If grit-blasting is not possible, grind the metal surface with 24-36 grit abrasive discs to a uniform, clean, bright metal surface with a 50¬75 microns anchor pattern. Use angle grinder on small areas.

Aluminium: Degrease with solvent or Super Cleaner. Sand well using 24- 120 grade (aluminium compatible) paper. Coarser grades are recommended to achieve optimum adhesion. Clean thoroughly and allow to dry. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems.

Zinc/Galvanised Steel: Degrease with solvent or Super Cleaner. Sand well using 60-120 grade paper. Clean thoroughly and allow to dry completely. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems.

Stainless Steel: Light grit blast to produce a profile of 50 microns. Clean thoroughly and allow to dry completely. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems.

Lead: Degrease with solvent or Super Cleaner. Sand well using 120 grade paper or power wire brush clean thoroughly and allow to dry. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems.

Bare Wood: Sand smooth with 80-180 and then 280 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying products recommended for application direct to wood (see specific coating systems).

Hazard Warnings

Hazard Pictogram :
Signal Word:	Warning
Hazard Statements:	Flammable liquid and vapour Causes skin irritation Causes serious eye damage May cause an allergic skin reaction Harmful to aquatic life with long lasting effects
Precautionary Statement:	General: Keep out of reach of children. Prevention: P210 - Keep away from heat / sparks / open flames / hot surfaces - No smoking P260 - Do not breathe mist / vapours / spray P261 - Avoid breathing dust / fume / gas / mist / vapours / spray P264 - Wash thoroughly after handling P272 - Contaminated work clothing should not be allowed out of the workplace P273 - Avoid release to the environment P280 - Wear protective gloves / eye protection / face protection Response: P301 310 IF SWALLOWED - Immediately call a POISON CENTER or doctor / physician P302 352 IF ON SKIN - Wash with soap and water P303 361 353 IF ON SKIN (or hair) - Remove / Take off immediately all contaminated clothing Rinse skin with water / shower P305 351 338 IF IN EYES - Rinse continuously with water for several minutes Remove contact lenses if present and easy to do - continue rinsing P310 - Immediately call a POISON CENTER or doctor / physician P321 - Specific treatment (see information on this label) P331 - Do NOT induce vomiting P333 313 - If skin irritation or a rash occurs: Get medical advice / attention P362 - Take off contaminated clothing and wash before reuse P363 - Wash contaminated clothing before reuse P370 - In case of fire P378 - Use alcohol resistant foam, CO2, powder, water spray for extinction. Do not use water jet Storage: P403 233 - Store in a well ventilated place. Keep container tightly closed. Disposal: P501 - Dispose of contents / container in accordance with local / national regulations.
Hazardous Ingredients	Epoxy Resin, N-Butanol, Xylene, Ethyl Benzene, Solvent Naphtha (petroleum), Light Aromatic, Amorphous Silica Gel, Aluminium Hydroxide.